MANUAL NO. 107999 REV. 04 (07/21/05)Operators & PartsManualMODELS:B124 H424GB130 B530AB130A H530AB142 H530AGB424 B742H424 H742B530B H742G
10Figures 4Operator’s GuideASSEMBLY INSTRUCTIONSModel 4241. Remove wooden blocks. Note: Watch for nails and wood splinters. Wear eye protection.2.
11Operating InstructionsAERATION TIPSShould I water before aerating?Best aerating condition is a soft and moistground. If you are unsure of the ground
12Figure 7REAR WHEEL ADJUSTMENTOperating InstructionsTHROTTLE CABLE ADJUSTMENT.Model 742 (Honda Engine Only)1. Start engine and allow it to reach oper
13Figure 8Operating InstructionsNOTE: Adjusting for greater stability will shortenthe length of the cores you pull. You will gaingreater side-to-side
14Operating InstructionsWhen operating on hills you shouldconsider the following:(A) Operate the machine up and down thehills rather than across them.
15Maintenance and Service InstructionsCLEANING AND WASHINGRegular cleaning, washing and lubricating willprolong the service of your machine.NOTE: Use
16Follow the engine manufacturers maintenanceinstructions. Should any malfunction occur withthe engine during the warranty period, take it toan Author
17Figure 12Maintenance and Service InstructionsClutch Cable Removal and Replacement1. Turn off engine and remove old clutch cable.2. Route new cable t
185. Remove the wheel shaft bearing bolts (4 on the424 and 530A and 6 on the 742).6. Remove the wheel axle assembly.Adjusting Chain Tension1. Turn eng
19Removable Wheel - Model 742 OnlyFigure 16Maintenance and Service Instructionscollar so that it rotates in the oppositedirection the wheel would norm
Lawn AeratorsWARNING: Engine exhaust, some of it’s constituents, and certain vehicle componentscontain or emit chemicals known to the State of Califor
20Figure 17Maintenance and Service Instructions8. Remove the tine rotor shaft bearing bolts (4).9. Remove chain scaper bolts (2) and chainscraper (on
21Parts Main Frame - Model 424ITEM PART NO. QTY. DESCRIPTION 1 ... 7144 ...2... WEIGHT, 36 LBS., SOLID STEEL 2
22Parts Handle and Control - Model 424ITEM PART NO. QTY. DESCRIPTION 1 ... 0034 ...2 ... GRIP, CLUTCH 2 ...
23Parts Rear Wheel - Model 424ITEM PART NO. QTY. DESCRIPTION 1 ... 0048 ...2... BEARING, ROLLER W/BUSHING &
24Parts Power Train & Tine Rotor - Model 424
25ITEM PART NO. QTY. DESCRIPTION 1 ... 0301 ...1... SPROCKET, JACKSHAFT, W/KEY & SPACER 2 ... 0302 ...
26Parts Main Frame - Model 530A
27ITEM PART NO. QTY. DESCRIPTION 1 ... 7600 ...2... WEIGHT, 36 LBS., SOLID STEEL 2 ... 7601 ...
28Parts Handle & Control - Model 530A123456789101112131415161718192021222366152066151524
29ITEM PART NO. QTY. DESCRIPTION 1 ... 0033 ...2... GRIPS, PAIR 2 ... 990209...2... SCRE
Operator’s GuideSPECIFICATIONSA) POWER UNIT 424 530A 742Engine 3.5HP Briggs I/C 3.5HP Briggs
30Parts Rear Wheel - Model 530A
31Parts Rear Wheel - Model 530AITEM PART NO. QTY. DESCRIPTION 1 ... 0048 ...2... BEARING, ROLLER W/BUSHING &
32Parts Power Train & Tine Rotor - Model 530A
33ITEM PART NO. QTY. DESCRIPTION 1 ... 7630 ...1... SPROCKET, JACKSHAFT, W/KEY & SPACER 2 ... 0302 ...
34ITEM PART NO. QTY. DESCRIPTION 1 ... 7600 ...2... WEIGHT, 36 LBS., SOLID STEEL, REMOVABLE 2 ... 7400 ...
35Parts Handle & Control - Model 742ITEM PART NO. QTY. DESCRIPTION 1 ... 0034 ...2... GRIP, CLUTCH, 1 EACH
36Parts Rear Wheel - Model 742
37ITEM PART NO. QTY. DESCRIPTION 1 ... 7409 ...2... BEARING, ROLLER W/SEALS 2 ... 7107 ...2..
38Parts Power Train & Tine Rotor - Model 742
39ITEM PART NO. QTY. DESCRIPTION 1 ... 7416 ...1... SPROCKET, JACKSHAFT, W/KEY 2 ... 7417 ...
4Figure 1MODEL 424 - FEATURES AND CONTROLSOperator’s Guide
40One Year Limited WarrantyFor one year from purchase, BlueBird will replace for the original purchaser, free of charge, any partor parts, found upon
5MODEL 530A - FEATURES AND CONTROLSOperator’s GuideFigure 2PoweredFront WheelRemovableWeightFolding HandleLocking CamRemovableWeightEngineGuardAdjusta
6MODEL 742 - FEATURES AND CONTROLSFigure 3Operator’s Guide
7Operator’s GuideGENERAL INFORMATIONThis manual will assist you in the safe operationand proper maintenance of your Husqvarnaequipment. Read it thorou
8The following decals are found on Model 424,530 and 742 aerators. If any are missing or notlegible, replace them before operating aerator.SAFETY AN
9DECAL PLACEMENT - MODELS 424, 530A AND 742Figure 3G2G1H (on deck behind engine)F (on back of housing over tine rotor)K (for Models
Kommentare zu diesen Handbüchern